Computational fluid dynamics of high density circulating fluidized bed riser: Study of modeling parameters

CFD modeling of air and fluid catalytic cracking (FCC) particles in the riser of a high density circulating fluidized bed (HDCFB) has been performed. The implementation of correct inlet conditions was found to be critical for the successful simulation of the hydrodynamics. The simulated profiles of gas and solid velocity and volume fraction were overall in good agreement with experimental data reported in the literature. However, due to the difficulties in accurate modeling of the solid segregation toward the wall, the solid volume fraction was under predicted near the walls. The effect of modeling parameters including different drag models, wall restitution coefficient values, and solid slip conditions have been evaluated. While the wall restitution coefficient did not exhibit a significant effect on the riser hydrodynamics, the appropriate slip condition aided in predicting the solid segregation toward the wall.     

Evolution of ferroelectric and piezoelectric response by heat treatment in pseudocubic BiFeO<Subscript>3</Subscript>–BaTiO<Subscript>3</Subscript> ceramics

Heat treatment of ceramics is an important process to tailor the fine electromechanical properties. To explore the criteria for optimized heat treatment in a perovskite structure of (1–x)Bi_1.05FeO₃–xBaTiO₃ (BF–BT100x) system, the structural phase relation, ferroelectric and piezoelectric response of BF–BT36 and BF–BT40 ceramics prepared by furnace cooling (FC) and quenching process were investigated. The X-ray diffraction examination showed single pseudocubic perovskite structure for all the ceramics. The homogenous microstructure was obtained for all ceramics with relatively large grain size in the furnace cooled samples. Well saturated ferroelectric hysteresis loops and enhanced piezoelectric constant (d₃₃?=?97 pC/N) were achieved by quenching process. Dielectric curve of BF–BT36 showed large dielectric constant at its Curie temperature, however, BF–BT40 showed diffused relaxor-like dielectric anomalies. Quenched BF–BT36 samples showed typical butterfly like field induced strain curves, however negative strain decreased in BF–BT40 ceramics. From these investigated study, it is observed that BF–BT ceramics are very sensitive to the heat treatment process (furnace cooling and quenching) on the dielectric, electromechanical properties.     

Tuning the interlaminar shear strength and thermo-mechanical properties of glass fiber composites by incorporation of (3-mercaptopropyl) trimethoxysilane-functionalized carbon black

The incorporation of functionalized nanoscale fillers into traditional glass fiber/unsaturated polyester (GF/UPE) composites provides a more robust mechanical attributes. The current study demonstrates the potential of 3-mercaptopropyl trimethoxysilane (MPTS)-functionalized carbon black (f-CB) for enhancing the thermo-mechanical properties of GF composites. The composites infused with 1, 3 and 5 wt% of pristine and MPTS-functionalized CB were fabricated by hand lay-up and hot press processing. Tensile testing, interlaminar shear strength (ILSS) testing and dynamic mechanical analysis were used to evaluate the performance of nanocomposites. Fourier transform infrared spectroscopy validated the MPTS functionalization of CB. Pristine CB-loaded nanocomposites exhibited marginal improvement in ultimate tensile strength (UTS), ILSS and thermo-mechanical properties. However, with the addition of f-CB, the improvement in all the studied properties was more substantial. The inclusion of 5 wt% f-CB increased the elastic modulus and UTS by 16 and 22%, respectively, whereas the ILSS was enhanced by 36%, in comparison to the neat GF composite. The scanning electron microscope analysis of fractured ILSS samples revealed better fiber-matrix adhesion and compatibility in f-CB-loaded nanocomposites. At the same filler weight percentage, the storage modulus at 25 °C was ~ 19% higher than that of neat composite. The f-CB inclusion resulted in increment of T _g by ~ 13 °C over the T _g of neat GF/UPE composite (~ 109 °C). These improvements were due to the chemical connection of f-CB to the UPE matrix and GF surface. With such improvements in thermal and mechanical properties, these nanocomposites can replace the conventional GF composites with prominent improvements in performance.     

Natural Palm Olein Polyol as a Replacement for Polyether Polyols in Viscoelastic Polyurethane Foam

The impact of replacing three polyether polyols with different levels of a single palm olein‐based natural oil polyol (NOP) was systematically correlated with the changes in foaming reactivity, cell structure, physico‐mechanical properties, and morphology of viscoelastic (VE) foams. The data show that replacing the polyether polyols with the NOP slightly increased the rate of the foaming reactivity. Increasing the NOP content resulted in increased cell size and cells remained fully open. Increased NOP content contributed to higher load bearing properties of VE foam, which can be attributed to higher functionality of NOP compared to polyether polyols. Addition of the NOP slightly increased the resilience of the foams, however, the hysteresis which is the measure of energy absorption remained mostly unaffected. Age properties, characterized by dry and humid compression sets, were mostly unaffected by the replacement of the polyether polyol with the NOP. The addition of NOP did not impact the morphology of the VE foam polymer matrix, which appears to retain a low degree of hard and soft segment domain separation. Overall, the results demonstrate a feasibility that the NOP can be used to partially replace the polyether polyols in VE polyurethane foams without significant impact on the functional performance.     

Near- and Far-Field Characterization of Planar mm-Wave Antenna Arrays with Waveguide-to-Microstrip Transition

We present the design and characterization of planar mm-wave patch antenna arrays with waveguide-to-microstrip transition using both near- and far-field methods. The arrays were designed for metrological assessment of error sources in antenna measurement. One antenna was designed for the automotive radar frequency range at 77 GHz, while another was designed for the frequency of 94 GHz, which is used, e.g., for imaging radar applications. In addition to the antennas, a simple transition from rectangular waveguide WR-10 to planar microstrip line on Rogers 3003? substrate has been designed based on probe coupling. For determination of the far-field radiation pattern of the antennas, we compare results from two different measurement methods to simulations. Both a far-field antenna measurement system and a planar near-field scanner with near-to-far-field transformation were used to determine the antenna diagrams. The fabricated antennas achieve a good matching and a good agreement between measured and simulated antenna diagrams. The results also show that the far-field scanner achieves more accurate measurement results with regard to simulations than the near-field scanner. The far-field antenna scanning system is built for metrological assessment and antenna calibration. The antennas are the first which were designed to be tested with the measurement system.     

Forecasting based on sectoral energy consumption of GHGs in Turkey and mitigation policies

Recently, global warming and its effects have become one of the most important themes in the world. Under the Kyoto Protocol, the EU has agreed to an 8% reduction in its greenhouse gas (GHG) emissions by 2008–2012. The GHG emissions (total GHG, CO₂, CO, SO₂, NO₂, E (emissions of non-methane volatile organic compounds)) covered by the Protocol are weighted by their global warming potentials (GWPs) and aggregated to give total emissions in CO₂ equivalents. The main subject in this study is to obtain equations by the artificial neural network (ANN) approach to predict the GHGs of Turkey using sectoral energy consumption. The equations obtained are used to determine the future level of the GHG and to take measures to control the share of sectors in total emission. According to ANN results, the maximum mean absolute percentage error (MAPE) was found as 0.147151, 0.066716, 0.181901, 0.105146, 0.124684, and 0.158157 for GHG, SO₂, NO₂, CO, E, and CO₂, respectively, for the training data with Levenberg–Marquardt (LM) algorithm by 8 neurons. R² values are obtained very close to 1. Also, this study proposes mitigation policies for GHGs.     

Cit-CSP及其应用

介绍了Cit-CSP--Cit/E-commerce信息安全保障平台子系统，并阐述了它所提供的消息摘要、块加密、加密(公钥)、签名和MAC等功能和服务。     

Microscale and mesoscale discrete models for dynamic fracture of structures built of brittle material

In this work we present the discrete models for dynamic fracture of structures built of brittle materials. The models construction is based on Voronoi cell representation of the heterogeneous structure, with the beam lattice network used to model the cohesive and compressive forces between the neighboring cells. Each lattice component is a geometrically exact shear deformable beam which can describe large rigid body motion and the most salient fracture mechanisms. The latter can be represented through the corresponding form of the beam constitutive equations, which are derived either at microscale with random distribution of material properties or at a mesoscale with average deterministic values. The proposed models are also placed within the framework of dynamics, where special attention is paid to constructing the lattice network mass matrix as well as the corresponding time-stepping schemes. Numerical simulations of compression and bending tests is given to illustrate the models performance.     

基于加载算法的室内无线信道OFDM接收机的性能

本文研究了无线局域网中使信号频谱得到优化的一种简单OFDM子载波加载算法。此算法基于边缘自适应（Margin Adaptive）加载准则及其在室内无线信道上的性能。     

Hydrodynamic effects on flow through screens at intakes

The effect of fish protective screens placed at an angle less than 90° to the flow was investigated. The effect of the approach velocity, wire area and the screen angle were considered. Mathematical equations were developed for determining the pressure drop coefficient and the angle of the flow downstream from the screen. It was found that these parameters depend primarily on the variables considered and on the drag coefficient. This finding is important for design considerations of intakes with this type of fish screen arrangement.